how do you release the water

Is it ment to remove some floor on the sea sovereign

@niqueil.bendak there is a medium winch on the inside roof of the "sea sovereign" helicopter that you can connect the top of the water bucket to. of course its going to be different for each helicopter design but some tips for this helicopter is don't make the cable length too small

I don't get how to put the add on on the helicopter

Ok ty

Keep it on longer cable, and don't fly erratically.

the bucket keeps hitting the blades and blowing up how do i fix it?

Ok, thanks. See these are the things I had no way to know, I've never used a bucket before. Copying and pasting the same instructions you gave for the water cannon--and I assume the rest of your addons--was more confusing than helpful.

After spawning you need to connect the bucket with a cable to winch inside helicopter, it is not self attaching

Ah. To the side? Wouldn't that unbalance the helicopter? Obviously moving it down wasn't gonna work, I tried anyway, but naturally the helicopter just dropped on top of it and fell over instead of winding up in any usable position. I think your other advice may be the only way. I'd have to go to a dedicated helicopter base though, I was trying it on Creative Base and I'm not going to be able to pick anything up while I'm inside the hangar.

What i included is basic steps for using selection grid tool, not all steps to connect the bucket

This bucket is universal for multiple helicopters so it doesn't have default position, you have to move it to the side manually

Mr. Noise, we are using the paste tool exactly as you instructed. I almost didn't, because it pasted over half the helicopter, but I tried it directly as instructed in the end, pasting it in default position with the helicopter in its default position. Unfortunately it pasted over a number of things, disabling half the avionics just for a start. It may have opened up the fuel tanks and left us empty, as the engines will not start; the fuel readout is in negative numbers.

So please don't insult us. We didn't misuse the paste tool; we followed your instructions exactly and the system does not work. Please revise your instructions.

Dear God

Just spawn the bucket as separate creation and use cable that is on board to connect it instead, if you don't know how to use paste tool properly.

where did u put the fuel tank

was going crazy

i did it but the helicopter

You know you need to move it to a side before you paste it in right?

it removes all fuel in the helicopter

Bucket is working. Connect it to central winch inside the helicopter.

?

can u fix the bucket

Both of those seem to be unrelated to the bucket itself.
And to use water cannon you need to select it on one of the middle MFD's, press "next screen" until you see the water cannon screen.

*did't*

I try refuelling it work

like it say on dial -7.50 something like that

so when it try to take off it says low fuel

also your water cannon when i press space it does't shoot

How about you explain what is wrong in more detail.

yes

what?

when put on the helicopter i get no fuel

by reading

how do i launch water

can someone tell me were the midle winch is becaus i dont see a thing accept for a Connector

Ohhhhhh my bad let me try it now

oh no the one on bucket is supposed to be there, it transmits power to the pump, you should use cable in the heli itself oppoisite the winch controls

If this makes a difference I use the blue cable connected to the bucket to hook it up to the heli...

No I use the mission editor and place it underneath. I test the mission location and then I hook it up.

oh do you spawn the bucket alongside the helicopter using merge tool? if you do that then bucket is one block too low and when you paste it in nozzles get deleted.

Yes I have connected the blue cable...
I pressed that button but when you press 3 in the cockpit it activates that automatically.

did you use blue calble to connect it? and did you try pressing button under winch controls? if that button doesnt work then i dont know what could be wrong.

So I have been using this, and I can’t get it to pump water out. I put this under water and it fills with water. Then I press 3 in the heli and nothing happens. I can clearly see that there is water in the bucket but nothing happens when I press 3. (Yes I connected the cable inside the middle winch)

nice