Suscríbete para descargar
Breakdancer - Working Fairground Ride

Hey Today I decided to upload a creation I designed quite a few months back. It is a fully functional recreation of a breakdancer ride found on fairgrounds around the world. The challenge was to make this creation be able to be folded into a trailer and transported with a single truck. I recommend downloading the provided truck for optimal functionality.
Note: This is one of my older creations and therefore will not feature the amount of detail that my newer creations do.


This trailer was entirely built by innosteve. Do not reupload without my permission.


----Instructions for Setup----
This is a step by step guide on how to set up and operate my Stormworks Breakdancer fairground ride.

NOTE. A stormworks bug causes creations to interfere, which has an impact on hinge strength. In case any hinges fail to operate correctly, try to resolve the problem, by adjusting the position of other creations (like for example the provided truck)

Like on a real fairground ride, this process requires a lot of skill and time to do. (setup takes me about 10 minutes)
--Setup:
1. Park the trailer at the desired location
2. Decouple it from the truck
3. Walk to the right side of the trailer, and press "Extend Fence". This will fold the side fence and give you access to the operations panel
4. Open the operations panel located under the side fence "Open Controls"
5. Extnd the supports by pressing "Supports"
6. Extend the power cable located inside the operations panel and connect it to a power source (the compatible truck can do the job if needed -> Switch the crane on for maximal power output)
(Note: In case the trailers batteries are too low to extend this cable there is a button in the operations panel labled "Charge Battery From Truck (Coupling)" which can be used to charge the trailers battery through the truck coupling)
7. On the sides of the trailer there are extendable supports. Press "Release Support" and pull the handle until you have the support at a 90° angle. Extend the support leg with the corresponding up and down buttons. Ensure that the leg is bent outwards so it cannot collapse.
8. Repeat step 7 on the other side of the trailer
9. Extend the front path by pressing "Extend Front Path" in the operations panel
10. Unlock the two floor plates by going to the back of the trailer where you will find two buttons labled "Disconnect"
11. Extend the floor winches using "Winch Down Left" and " Winch Down Right" in the operations panel
12. Fold the floor plates down (This will require some manual pushing agains the plates)
13. Lock the floor plates with the same buttons that were used to unlock them
14. Extend the front flip feet on the front corners using the "up" and "down" buttons at the sides of the floor plates
15. Press "Unlock Arms" (Operations Panel)
16. Extend the arms (Operations Panel)
17. Extend inner floor 1: "Extend Rotation Plate 1"
18. If inner floor 1 is fully extended, extend inner floor 2: "Extend Rotation Plate 2"
19. Unlock the outside parts: "Unlock Outsides"
20. Extend the gondolas: "Extend Gondolas" -do NOT unlock them yet-
21. Unlock the free spinning gondolas: "Unlock Gondolas"
22. Unlock the operator cabin using the "Unlock Cabin" button located on the side if the cabin facing the ride
23. Pull the cabin on the rails outside all the way up to the connector.
24. Connect the cabin to the outside magnet by pressing "Connect Cabin"
25. Turn on the lights (operations panel)
26. Tilt up the fences of the front path using the provided button on the fence itself: "Extend Fence"

The Following steps are relatively time consuming and not required for the ride to function. I would not actually recommend mounting all the fences ;)
27. All open ends of the floor plate have a button to connect or extend a fence. The fence parts can be found on the provided truck. IMPORTANT NOTE: Only disconnect one fence at a time and never leave two fences in a non-connected state



--Operation
1. Press "Enable ride"
2. Operate the ride using the two throttle levers
3. When done, press "Enable ride" again to disable the ride system


-- Folding back to trailer
1. Turn off the lights
2. Reove ALL fences placed in setup step 27 and ensure that the back left side fence is retracted
3. Fold the fences of the front path
4. Press "Lock Gondolas" and ensure all the gondolas are connected to their lock magnet -> if that is not the case, manually position the missalligned ones
5. Fold the gondolas back together ("Extend Gondolas")
6. Lock the outsides and ensure they are all connected to their magnet -> if not, manually rotate them by HAND
7. Fold the inner floor up (FIRST 2 THEN 1)
8. Retract the arms
9. Use the "Rotate Center" button to move the ride arms so they are alligned with the trailer for connecting
10. Only if step 9 is properly completed, press "Unlock Arms" to lock the ride to the trailer
11. Disconnect the cabin (undo setup step 24)
12. Push the cabin onto the trailer and lock it as soon as it is centered
13. Retract the flip feet (undo setup step 14)
14. Unlock the floor plate (undo setup step 13)
15. Retract the floor plates using the winch controls located in the operations panel
16. Retract the side supports (setup step 7) and ensure they are flush with the trailer
17. Lock the floor plates to the trailer using the buttons located at the back of the trailer
18. Retract the front path (ensure the fences are at a 45 degree angle)
19. Retract the supports
20. Retrack the power cable and close the operations panel
21. Fold the side fences